Can i change itouch battery

As soon as the solder has flowed into the joint, remove both the solder and the iron. Remove the piece of tape covering the remaining two leads. If you are satisfied with the position of the cable relative to the pads on the board, proceed. If not, de-solder the first connection and try again. Solder the two remaining pads to the logic board, being mindful of overheating the cable or board. Don't forget to reapply the piece of tape over the solder pads to prevent any shorts. Cancel: I did not complete this guide.

Badges: Otherwise this will break all of your plastic pieces that are glued to your touch screen. Another thing is I removed one of the contacts from the circuit board while removing the battery. I thought the ipod was toast. But upon further investigation I realized that that contact went though the board. So I scraped that area down to the other contacts and applied solder to it.

Then I was able to reinstall the new battery. Be careful when you insert your ipod opening tool into your device in step 2 and step 3. The ipod opening tool shouuld be inserted between the metal part and the rubber pad, not between the rubber pad and the edge of touch screen. It will damage your rubber pad surrounding the touch screen. Even though I did some damage to the rubber pad, it looks good when I finish the replacement :.

Did it! Taking apart the case of the Touch first steps was the hardest part. Soldering the battery in was a bit tricky. I tinned the connectors prior to soldering and that made it much easier than adding solder later.

Reassembly took only about 20 minutes. Disassembly was about 45 minutes. Broke left side of plastic frame around glass front but when reassembled its no problem. You would never know it.

I'm really pretty good at electronic assembly and I would agree that its very difficult. Refer to this thread and I would suggest not desoldering the old pads. This happened to me and I was careful and work with electronics everyday. Soldering point for iPod touch 2nd generation battery. Fix Your Stuff Community Store. Difficulty Very difficult.

Steps Time Required 1 - 4 hours. Sections 3. Front Panel 8 steps Display 9 steps Battery 9 steps. Flags 1. Featured Guide This guide has been found to be exceptionally cool by the iFixit staff. Introduction Use this guide to replace a worn-out battery on your 2nd generation Touch. Step 1 Front Panel. Add a comment. Add Comment Cancel.

Step 2. Find an authorized service provider near you at Apple's website. Repair Shops: Many websites and mall kiosks offer iPhone and iPod battery replacement services, often with prices lower than Apple's. Be wary of these options.

Unless they're authorized by Apple, their staff may not be experts and they could accidentally damage your device. This is a little trickier, but your favorite search engine can supply you companies that sell the tools and battery you need.

Otherwise, you could end up with a dead device. For the iPhone, Apple will service the battery on models as old as the iPhone 3GS up to the most recent. For iPods, Apple only services the battery on more recent models. If you've got an iPod that's a couple of generations old, you may have to find other repair options.

Check with Apple to see if your model is covered. For the most up to date pricing and terms, check out Apple's pages for iPhone repair pricing and iPod repair pricing.

Replacing the dead or dying battery in your iPhone or iPod may seem like a good idea, but it may not be worth it. It depends on how old the device is. We recommend thinking about the issue like this:. In the last case, you need to weigh the cost of replacing the battery against the cost of a new device.

For example, if you've got a 5th Gen. For that price, you get all the latest hardware and software. Why not spend a bit more and get a much better device? You can avoid needing battery replacement as long as possible by taking good care of your battery. Apple suggests doing the following things to give your battery the longest possible lifespan:. Those are tips to make your battery have a longer lifespan, but that's not the same thing as getting more use out of a single charge.

Actively scan device characteristics for identification. Use precise geolocation data. Select personalised content. Lift up the top of the iPod and slide it slightly upward to disconnect the exterior hold switch from the switch on the interior circuit board. Slowly lift the top cover off of the iPod and turn it so that the face is now pointing down toward the towel.

Do this as if you were opening the front cover of a book. Don't jerk the front cover or move it too far away from the iPod case, because it is still connected to the circuit board inside.

Grasp with a pair of needle-nose pliers the battery connector located at the bottom of the circuit board and pull it off the board. Nathan McGinty started writing in He has worked in the technology industry for more than 20 years, in positions ranging from tech support to marketing. By Nathan McGinty.